4 AXIS CNC Router or Mill Complete Kit Stepper Driver Board and NEMA23 Stepper Motor *4 and Power Supply
Features:
- Toshiba TB6560AHQ chip - High power, maximum 3.5A drive current chipset !
- 1-1/16 ( 1/2,1/4,1/8,1/16 )microstep setting - Higher accuracy and smoother operation than standard 1, 1/2 step!
- Adjustable 1.5A-3A drive current settings for each axis - 25%,50%,75%,100% of full current can be set for different stepper motors
- Overload, over-current and over-temperature safety - Full protection for your computer and peripheral equipment !
- On board current switching - Power output can be set according to specific user requirement !
- Full closed-type optical isolation to protect the user's computer and equipment
- Relay spindle interface - Outputs Max. 36V 7.5A for spindle motors or coolant pump (only one device can be powered by this output!)
- 4 channel inputs interface- Can be used for XYZ limit and emergency stop !
- Professional design - Two stage signal processing with super anti-jamming !
- Bipolar constant current chopper drive with non-resonant region - Controls motors smoothly through range without creep effect !
- Four control inputs (divided into pairs of knives) - Allows setting of limit and emergency stop !
- Universal architecture - Supports most parallel software MACH3,KCAM4 etc!
Dip settings:
| Current Setting |
1 |
2 |
Decay Mode Settings |
3 |
4 |
MicroStep Settings |
5 |
6 |
| 100% |
ON |
ON |
FAST |
ON |
ON |
1 |
ON |
ON |
| 75% |
ON |
OFF |
25% |
ON |
OFF |
1/2 |
ON |
OFF |
| 50% |
OFF |
ON |
50% |
OFF |
ON |
1/8 |
OFF |
ON |
| 25% |
OFF |
OFF |
SLOW |
OFF |
OFF |
1/16 |
OFF |
OFF |
Further Details:
- Power supply DC 12-36V (not included in this listing. Please feel free to check our other listings include power supply)
- This driver and the steppers get power from the same unit, they don't require separate power source.
- Voltage Selection:
- 12-16V DC power supply for Nema 17 stepper motors
- 16-24V DC power supply for Nema 23 stepper motors
- 24-36V DC power supply for Nema 34 stepper motors
- Important: High voltage will burn up the chips or stepper motors
- Ampertage Selection:
- Output current of the power supply can be calculated by the following expressions:
- Output current = Rated current of your stepper motors * quantity + 2A
For example, if you want to drive 3 * 3A Nema 23 stepper motors, theoretically 24V 11A DC power supply is recommended, but higher power such as 24V 15A also will be good.
If you are not sure about the selection of power supply, please feel free to contact us for help.
- The power output of 12V shall be applied to the radiator fan of 12V
- Driver output compatible with 2 or 4 phase, 4,6 or 8 lead stepper motors, 3A max.
- Suitable for unipolar or bipolar stepper motors.
- Voltage regulated spindle speed controlled by parallel interface as function of supply voltage
Data Sheet for 57BYGH56-401A Stepper Motor:
|
Model |
Step angle |
Motor length |
Rated current |
Phase resistance |
Phase inductance |
Holding torque |
Lead wire |
Weight |
|
Single Shaft |
o |
L (mm) |
A |
Ω |
mH |
Oz-in |
kgf.cm |
No. |
kg |
|
57BYGH56-401A |
1.8 |
56 |
2.8 |
0.9 |
2.5 |
175 |
12.6 |
4 |
0.7 |
This 57BYGH56-401A Stepper Motor is designed according to performance of TB6560AHQ driver board. They are the best match. If customer need other motor, please feel free to check following model data sheet.
Package included:
- 1 x 4 Axis TB6560 Driver Controller
- 4 x Nema 23 57BYGH56-401A Stepper Motor
- 1 x DB25 parallel cable
- 1 x 24V Power Suply
|
